Horns are a pain in the butt. You have only a few good options when you need them for your cosplay. You can buy real horns…. but that’s pricey, or you can make your own but that can be messy….. or is it!!
Quick background on this project. I needed a set of 4 horns for a shield. These needed to be over 12 inches long and pretty thin. I got lucky on this and had a form I could use, but these could easily be done free hand as well.
Materials:Expanding foam and wire mesh, that is all you will need.
Total cost $9.00 on the mesh (enough for 2 big horns)
$4.99 on the foam (still haven’t used it all up)
Cost per horn…. about $4.00 dollars for me. Price will vary a bit but this is much much cheeper then other methods and the end product is strong and able to take some abuse.
How to do it:
Start with a general idea of how you want this horn to look
Is it wide at the bottom?
Long and Narrow?
Short and thin?
I used a form from another horn I had
I split the mesh in half lengthwise and used it to wrap the horn.
Once its wrapped and you’re happy with the over all look, I recommend a few dobs of hotglue to help it hold its shape. The mesh is very bendable but it will always have a bit of spring to it.
Horn copy is almost done,
You should be asking your self “Where is the spray foam” or at least wondering why you purchased it at this point. This wire form is a great way get the look of a horn but is not very tough. I have seen many tutorials out there where people start to cover the horn at this point with paper mache or even fiberglass.
Time to fill the form with the spray foam, I left the end open so I could get the nozzle of the spray foam down in to it to help fill the horn. There are also a few small holes cut in the mesh just to make sure I can get the whole thing filled.
I have also mounted them on a wooden dowel because that’s how my costume needs them :)
I failed to take any good pictures of the process of filling them with foam, but its not really something you should need help with. Put the can together, stick the straw in to the horn, and fill full of foam. If some squirts out of the mesh that’s fine. You can wipe it off once you’re done filling it full.
Here are all 4 of the horns I did drying. The foam will take 8 hours to cure to full strength and will expand through the mesh and look a bit like an alien egg…. or something..
Next day and the foam is dry. Using a sharp knife, cut away the extra foam and don’t worry about being very gentle, the mesh will keep you from cutting too deep and ruining your hard work.
Total weight of the 4 horns and dowel is under 2 pounds.
Prep your horn with a good sanding of 80-120 grit sand paper and finish with your method of choosing. Paper mache will work very well to help keep it light.
Hope this helps and best of luck with all your cosplay work!
Do you suggest this method over the mesh & paperclay method? I really like how easy it seems to just spray the foam, let it cure, sand, voila — your form is done. The paperclay method seems a lot more involved.
I haven’t tried yet myself, but I would hazard a guess and say that these two methods would work great together. The foam provides a strong and durable structure to work over.
This would allow you to roll out a nice think and smooth coat of Paper clay and coat the structure with that. No matter what look you’re going for, you’re going to want to apply a coating of some sort to the foam filled frame.
This method that I describe was designed to help with the strength problems associated with a lot of other horn tutorials.
Aha, I understand now. ^^; Thanks for being so helpful!
where did you buy the mesh wire from?
We got it at Michael’s, you can also get it online: http://www.scrap-masters.com/-activwire-mesh-12×24-sheet-p-219271.html
I don’t know if you’re still keeping an eye on this or not, but would you think that that plastic mesh… uh, plastic canvas screen, I think it’s called… would work, also? I’d imagine that it’d be lighter than metal mesh, but do you think it would still do the job?
Or should I just throw caution to the wind and give it a shot?
Hi! If the plastic screen can bend and hold it’s shape, then it will work. We used the metal mesh to give the horn it’s shape, so as long as the plastic will stay where you put it, then it should be fine. Mario also says that if you’re worried about weight as well, then use newspaper strips of paper mache instead of the paste that we used, it would be much lighter and also dry quicker. Hope that helped!
Alright cool ^_^ Thanks for the advice. I’d hate to be a bother, but do you have any other ideas for what I could do to make them super-light? I have to mount them onto a headband somehow and wear them for a good while, so… yeah. I’m trying to get all the ideas I can.
If a picture of what I’m doing would help, this is the character I’m dressing up as: http://th05.deviantart.net/fs35/PRE/f/2008/299/7/7/Witchblade__Maria_by_Infamous_Mr_Oob.jpg
Thank you for your help so far!
Maybe use expanding foam with a cardboard core, or sheets of pink foam carved into the shape you need, covered with paper mache or maybe fiberglass resin, it might be lighter than paper mache but much harder to work with.
Awesome! *o* I never would have thought of any of this. Thank you so much for your help.
This might be a stupid question, but you take off the mesh once it’s done, right?
And the sand it down and what not?
Sorry for the late reply! No, you leave the mesh on, it is what gives the horn structure, and the paper mache is on top of it. It can be sanded, yes!
MUST DO IT! I thank you for tihs guide!
Thanks for this! I’ve been wrestling for ages how to make a big headdress and you’ve confirmed for me that it will work and it is a good idea! Thanks for your tips :D